If your GE/CADDX security panel is set to its default settings, press. 8 9 7 1 3 7 2 # for NX-8/6/4 or. 8 9 7 1 3 0 # for NX-8e from the Caddx keypad to begin programming. Page 3 If still no activity is observed: a) Remove power from the security system then reapply it.
ARMING IN 'EXIT' MODE EXIT is used when the user is away from the premises
and wants the interior protected (the motion detectors ON).
- Modular systems. Up to 32 modules can be added to expand the capabilities of the NX-8. ORDERING INFORMATION CADDX PART # DESCRIPTION NX-8 KIT Includes NX-8 Control, NX-108E LED Keypad, & 16.5V 25VA Transformer NX-8 NX-8 Control Only NX-108E 8 Zone LED Keypad NX-116E 16 Zone LED Keypad NX-124E 24 Zone LED Keypad NX-148E Alphanumeric LCD Keypad.
- ORDERING INFORMATION CADDX PART # DESCRIPTION NX-8 KIT Includes NX-8 Control, NX-108 LED Keypad, & 16.5V 25VA Transformer NX-8 NX-8 Control Only NX-108 8 Zone LED Keypad NX-116 16 Zone LED Keypad NX-124 24 Zone LED Keypad NX-148 Alphanumeric LCD Keypad NX-200. Zone Doubling Kit (Includes 100 3.74k and 100 6.98k resistors).
ARMING IN 'STAY' MODE STAY is used when the user is inside the premises and
wants protection around the perimeter (the motion
DISARMING SYSTEM Enter code.
How To Program Caddx Nx 8 Wiring Diagrams
user code, enter * * * * for a 4-digit code.
How To Program Caddx Nx 8 Wiring Manual
7. Press the '#' key while the ready light is flashing to
BYPASSING ZONES System must be in disarmed state.
ARMING IN 'EXIT' MODE EXIT is used when the user is away from the premises
and wants the interior protected (the motion detectors ON).
- Modular systems. Up to 32 modules can be added to expand the capabilities of the NX-8. ORDERING INFORMATION CADDX PART # DESCRIPTION NX-8 KIT Includes NX-8 Control, NX-108E LED Keypad, & 16.5V 25VA Transformer NX-8 NX-8 Control Only NX-108E 8 Zone LED Keypad NX-116E 16 Zone LED Keypad NX-124E 24 Zone LED Keypad NX-148E Alphanumeric LCD Keypad.
- ORDERING INFORMATION CADDX PART # DESCRIPTION NX-8 KIT Includes NX-8 Control, NX-108 LED Keypad, & 16.5V 25VA Transformer NX-8 NX-8 Control Only NX-108 8 Zone LED Keypad NX-116 16 Zone LED Keypad NX-124 24 Zone LED Keypad NX-148 Alphanumeric LCD Keypad NX-200. Zone Doubling Kit (Includes 100 3.74k and 100 6.98k resistors).
ARMING IN 'STAY' MODE STAY is used when the user is inside the premises and
wants protection around the perimeter (the motion
DISARMING SYSTEM Enter code.
How To Program Caddx Nx 8 Wiring Diagrams
user code, enter * * * * for a 4-digit code.
How To Program Caddx Nx 8 Wiring Manual
7. Press the '#' key while the ready light is flashing to
BYPASSING ZONES System must be in disarmed state.
2. Enter 1 or 2 digits indicating the zone you wish to
bypass. (Example: Press the '1' key for zone 1,
4. The corresponding zone light will illuminate indicating
the zone has been bypassed. Repeat steps #2 and #3 for
any other zone(s) that need to be bypassed.
5. Press the '#' key to exit the Bypass Mode. The bypass
light will stop flashing upon exiting the Bypass Mode.
All zones will automatically be unbypassed each time the
system is disarmed.
2. The ALARM MEMORY feature will flash those zones
that created alarms and will light steady those zones that
IDENTIFYING TROUBLES
FLASHING ARMED LIGHT The armed light will flash when there has been
an alarm during the previous arm cycle.
POWER LIGHT OFF No AC power.
POWER LIGHT FLASHING Low system battery.
FIRE LIGHT FLASHING Trouble with fire device or wiring.
ZONE LIGHT FLASHING RAPIDLY A zone is in a trouble condition.
SERVICE LIGHT IS ON Press '*2' for further information (indicated by
zone lights).
Zone 1 – System fault.
Zone 2 – Zone tamper.
Zone 5 – Zone trouble.
Zone 6 – Telephone trouble.
Zone 7 – Dialer failure.
Zone 8 – System lost time.
Enter '#' to exit mode.
Nx 8 Panel
ENTER CODE TO SILENCE TROUBLE BEEPS.
ENTER '*7' TO ATTEMPT TO RESET TROUBLES.
ENTER CODE TO CLEAR SERVICE LIGHT AFTER A PHONE TROUBLE HAS BEEN CLEARED.
Caddx Nx 8 Programming Manual
SET CLOCK 1. Press '*97.'
How To Program Caddx Nx 8 Wiring Kit
